Mounts
- $1.90SKU: 7471
ENS 7471 Weatherproof Single Gang Device Mount Cover Blank
- Blank weatherproof cover plate for single-gang weatherproof electrical boxes; seals the box opening with a weatherproof gasket seal — no device opening, no device mount features; blank closure only
- Used when a conduit-fed box is installed but no device is currently connected, when a box is taken out of service and must be sealed, or as a placeholder during rough-in when the final device has not yet been selected
- Aluminum construction
$1.90Low Price Guarantee - $54.93SKU: 7302
ENS 7302 3/4 Weatherproof Boxes Double Gang 4" Round Box Aluminum
- 3/4" trade size weatherproof aluminum double-gang 4" round junction/device box; for outdoor exposed 3/4" EMT conduit installations
- 3/4" conduit entry hubs accommodate 3/4" EMT or rigid conduit connections — the correct box when the camera or device conduit run uses 3/4" conduit for higher conductor fill
- Aluminum construction for corrosion resistance in outdoor, wet, and coastal installations; double-gang capacity for two devices or a combination of device and blank cover
$54.93Low Price Guarantee - $54.93SKU: 7301
ENS 7301 1/2 Weatherproof Boxes Double Gang 4" Round Box Aluminum
- 1/2" trade size weatherproof aluminum double-gang 4" round junction/device box; designed for outdoor exposed conduit installations
- 1/2" conduit entry: pre-drilled or tapped 1/2" hubs accommodate 1/2" EMT or rigid conduit connections; aluminum construction resists corrosion in outdoor, coastal, and wet-environment installations
- Double-gang: accommodates two devices (receptacles, switches, keystone inserts) side-by-side in a standard double-gang configuration for outdoor installation points
$54.93Low Price Guarantee - $84.00SKU: S-C-PANEL-2U18
ENS S-C-PANEL-2U18 Cabinet Plate, 2U, 19 x 18"
- 2U blank rack filler/mounting panel; 19" wide; 18" depth; steel construction
- Fills 2U of unused rack space while providing an 18-inch deep mounting surface — the correct specification for deeper rack cabinets (24" or 30" deep) where a 15" panel would not span the full rack depth
- Maintains proper airflow by covering open rack slots; prevents hot air recirculation between the front and rear of the rack
- Mounts in standard 19" rack rails using standard rack screws; for the 15-inch depth variant
$84.00Low Price Guarantee - $72.00SKU: S-C-PANEL-2U15
ENS S-C-PANEL-2U15 Cabinet Plate, 2U, 19 x 15"
- 2U blank rack filler/mounting panel; 19" wide (standard rack width); 15" depth; steel construction
- Fills 2U of unused rack space in an equipment cabinet — blank panels maintain proper airflow by preventing hot air from equipment areas from recirculating through open rack slots
- 15-inch depth provides additional mounting real estate for attaching components, cable management accessories, or custom hardware to the inside of the panel
- Mounts in standard 19" rack rails using standard rack screws; the correct specification for 2U of rack space in installations where 15" panel depth is required or preferred
$72.00Low Price Guarantee - $170.00SKU: S-CABINET9U-W
ENS S-CABINET9U-W Open Frame Sever Cabinet, 9U, Wall Mountable
- 9U open frame wall-mount server cabinet; standard 19" rack mounting rails; no side panels or front door — maximum airflow and cable access from all sides
- 9U capacity: accommodates a complete mid-size security system stack — NVR (1–2U), PoE switch (1U), patch panel (1U), UPS (1–2U), and accessories — with more room than the 6U model and more compact than the 12U
- Open frame design: no panels restricting airflow or cable access; all sides of the rack remain accessible for cable routing, heat dissipation, and equipment service
- Wall-mount configuration: mounts to studs or masonry, keeping equipment elevated and organized without requiring floor space in the equipment area
$170.00Low Price Guarantee - $74.00SKU: BRACKET13-W
ENS BRACKET13-W Wall Mount for IP-5PT4IEN8-4X
- Aluminum alloy material with surface spray treatment
- Camera cables can be perfectly collected to the bracket so that the installation look more elegant
- Wall mounting bracket for dome cameras
- Dust-proof design
$74.00Low Price Guarantee - $60.00SKU: B15-W
ENS B15-W Waterproof Junction Box B15-W for IP-5VPXXX3/MZ
- Aluminum alloy material with a surface spray treatment
- Camera cables can be perfectly collected to the junction box so that the installation looks more elegant
- Bottom inlet and side inlet
- Wall or ceiling mounting
- Water-proof design
$60.00Low Price Guarantee - $50.00SKU: PTM-512
ENS PTM-512 Pendant Mount for IP-5DT8E3N2-36
- Designed for IP-5DT8E3N2-36 Camera: Engineered for precise compatibility and secure mounting
- Durable Construction: Made from high-quality materials to provide long-lasting support and reliability
- Versatile Mounting Options: Suitable for pendant or ceiling installations to fit various surveillance requirements
- Optimized Camera Positioning: Enables proper placement for optimal camera coverage and performance
- Easy Installation: Designed for quick and straightforward setup with the specified camera model
$50.00Low Price Guarantee
Mounts Frequently Asked Questions
What types of mounts are available for surveillance cameras?
There are several types of mounts available for surveillance cameras, including wall mounts, pole mounts, pendant mounts, and junction boxes. Each type serves a specific purpose, allowing for flexible installation options based on the camera's location and the environment. For example, wall mounts are ideal for fixed installations, while pole mounts can be used for cameras on tall structures.
How do I choose the right mount for my camera?
To choose the right mount for your camera, consider the camera's weight, the installation surface, and the desired angle of view. Ensure that the mount can support the camera's weight and is compatible with its design. Additionally, evaluate the environment where the camera will be installed, as some mounts are designed for outdoor use and may offer weather resistance.
Can I use the same mount for different camera models?
While some mounts are compatible with various camera models, many are designed specifically for certain types or brands. It is crucial to check the mount's specifications and compatibility with your camera model before purchasing. Using an incompatible mount can lead to instability or damage to the camera.
What materials are commonly used for camera mounts?
Camera mounts are typically made from materials such as aluminum, steel, or plastic. Aluminum and steel mounts are preferred for their durability and strength, especially in outdoor settings, while plastic mounts may be used for lighter indoor applications. The choice of material can affect the mount's longevity and ability to withstand environmental conditions.
Are mounts adjustable for different angles and positions?
Many camera mounts feature adjustable components that allow for changing angles and positions. These adjustments can help optimize the camera's field of view and ensure it captures the desired area. However, not all mounts have this capability, so it is important to verify the adjustability of a specific mount before purchasing.
Filter
Shopping Options
