Installation Tools & Supplies
- $18.40SKU: 96-0235100
Kramer 96-0235100 USB 3.2 Gen–2 Full Featured USB–C (F) to USB–C (M) Cable
- Quality Construction - Triple shielding that helps prevent electromagnetic interference and ensures reliable data communication
- Reversible USB Type–C Connector with integrated locking mechanism
- Video 4K@60 4:4:4 (DP Alt mode)
- Transfer Rates - Up to 10Gbps, USB 3.2 Gen 2
- USB 2.0
$18.40Low Price Guarantee - $16.00SKU: 96-0211005
Kramer 96-0211005 USB Active Extender Cable, 5 Meter
- True Plug–and–Play - No additional drivers needed
- USB 2.0 High Speed (480Mbps) Standard
- Construction - 1 pair 24AWG + 2 pair 22AWG + drain wire 24AWG, tinned copper braid
- No External Power - Pulls power from source
- Data Transfer Only - Not for charging
$16.00Low Price Guarantee - $17.60SKU: 91-000185
Kramer 91-000185 Power Cord UK Type C-19 180cm
- C-19 (female IEC connector) to UK British standard (BS 1363 Type G, 13A fused) plug; 180cm length; for Kramer equipment with C-20 power inlets
- UK Type G (BS 1363): three rectangular pin plug with an internal 13A fuse; mandatory for UK new installations; the fused plug provides an additional protection point at the plug itself, standard in British electrical practice
- C-19/C-20 pair rated for up to 16A at 250V; UK 230V AC 50Hz supply; 180cm length for standard rack-to-PDU routing
$17.60Low Price Guarantee - $17.60SKU: 91-000186
Kramer 91-000186 Power Cord Japan Type C-19 180cm
- C-19 (female IEC connector) to Japanese standard (JIS C 8303 Type A polarized with ground, or Type B) plug; 180cm length; for Kramer equipment with C-20 power inlets
- Japanese power standard: 100V AC at 50 Hz (eastern Japan) or 60 Hz (western Japan); Japanese outlets use non-polarized two-pin (Type A) or grounded three-pin (Type B) plugs similar to North American style but specifically rated for Japan's 100V system
- Confirm the Kramer equipment's accepted input voltage range includes 100V before deploying in Japan - most modern switching power supplies accept 100-240V; verify before installation
$17.60Low Price Guarantee - $17.60SKU: 91-000184
Kramer 91-000184 Power Cord Israel Type C-19 180cm
- C-19 (female IEC connector) to Israeli SI 32 (Type H) plug; 180cm length; for Kramer equipment with C-20 power inlets
- Israeli Type H plug uses a unique Y-shaped arrangement of three flat pins (two current-carrying + ground) not compatible with any other regional standard - the SI 32 plug is mandatory for Israeli electrical code compliance on equipment over certain power thresholds
- C-19/C-20 connector pair rated for up to 16A at 250V for higher-current equipment
$17.60Low Price Guarantee - $17.60SKU: 91-000183
Kramer 91-000183 Power Cord Australia Type C-19 180cm
- C-19 (female IEC connector) to Australian/NZ Type I plug; 180cm length; for Kramer rack-mount equipment with C-20 power inlets typically found on higher-current-rated power supplies and UPS units
- The C-19/C-20 connector pair is rated for up to 16A at 250V - used on equipment with higher power draw than the standard C-13/C-14 (10A) connector pair; the C-19 female end connects to the equipment's C-20 inlet
- 180cm cord length accommodates standard rack-to-PDU distances; Australian Type I plug for AU/NZ power outlets
$17.60Low Price Guarantee - $46.40SKU: 99-9318250
Kramer 99-9318250 Bulk Speaker Cable 18AWG - Plenum Rated, 250'
- 18 AWG stranded 2-conductor speaker cable; CMP (Communications Multipurpose Cable Plenum) rated; 250-foot reel
- Plenum-rated (CMP): required by the National Electrical Code (NEC Article 800) for cable routed through air-handling ceiling plenums and HVAC return-air spaces in commercial buildings - plenum cable uses flame-retardant, low-smoke materials that meet the more stringent NEC plenum fire safety requirements vs. CMR riser-rated or CM-rated cables
- 18 AWG wire gauge is appropriate for background music and paging applications at typical distributed audio levels and run lengths (up to approximately 50 feet per conductor at 8Ω for less than 0.5dB loss); for longer runs requiring lower resistance, see the 14 AWG 99-2416300
$46.40Low Price Guarantee - $360.00SKU: 99-0450100
Kramer 99-0450100 Four–Pair Cat7a S/FTP Data Bulk Cable (23AWG)
- Quality Construction - 4 individually aluminum–foil shielded twisted pairs (S/FTP), cabled with a drain conductor and overall braid–shielded
- Optimized for Kramer Hardware - Use with any of Kramer’s wide range of twisted pair digital transmitter–receiver sets. Terminate with shielded RJ–45 connectors
$360.00Low Price Guarantee - $483.20SKU: 99-0440300
Kramer 99-0440300 Cat6 Cable for Digital Tx/Rx (1000')
- Cat6 UTP solid-conductor 23 AWG bulk cable; 1,000-foot reel; validated for use with Kramer HDBaseT, DGKat, and other digital Tx/Rx extender systems
- Kramer-validated cable for digital extenders: the Cat6 parameters (characteristic impedance, attenuation, NEXT, return loss) of this specific cable are known to meet Kramer extender requirements - using validated cable reduces the risk of signal issues at maximum extension distances that unvalidated generic Cat6 may exhibit
- Solid-conductor 23 AWG construction is the correct cable type for in-wall and structured cabling runs; for patch cords and flexible jumper applications, stranded conductor cables are preferred
$483.20Low Price Guarantee
Installation Tools & Supplies Frequently Asked Questions
What tools do I need to install a surveillance camera?
To install a surveillance camera, you'll typically need a drill, screwdriver, and various installation tools like cable strippers and crimpers. Additionally, having a level and measuring tape can help ensure proper placement. Depending on the type of camera, you may also need specific cables, connectors, and mounting hardware, which are often included in the camera kit.
How do I choose the right cable for my surveillance system?
The right cable for a surveillance system depends on the camera type and distance from the recording device. Common options include coaxial cables for analog cameras and Ethernet cables for IP cameras. Ensure the cable is compatible with your system's specifications, such as gauge and shielding type, to maintain video quality and prevent interference.
What is the purpose of a keystone jack in surveillance installation?
A keystone jack is used to connect cables in a structured wiring system, providing a secure and organized way to connect surveillance cameras to networking equipment. It allows for easy insertion and removal of cables, facilitating maintenance and upgrades. Using keystone jacks can help manage cable clutter and improve the overall aesthetics of your installation.
Do I need special tools for terminating alarm wire?
Yes, terminating alarm wire requires specific tools, such as a wire stripper, crimper, and possibly a punch-down tool for connecting wires to terminals. These tools ensure proper connections and minimize signal loss, which is crucial for the reliability of your alarm system. Using the right tools can also prevent damage to the wires during the termination process.
What should I consider when selecting installation supplies for my surveillance system?
When selecting installation supplies, consider the type of surveillance system, the environment (indoor or outdoor), and the distance between components. Look for high-quality cables, connectors, and tools that match the specifications of your cameras and recording devices. Additionally, ensure that the supplies are compatible with the installation location to avoid issues like signal loss or physical damage.
Filter
Shopping Options
