Installation Tools & Supplies
- $78.00SKU: CW2516-KIT
ENS CW2516-KIT Raceway Cord Cover Kit, 3.5 Feet (10 Covers), Connectors & Accessories Included
- Complete CW2516 25 × 16mm raceway kit; 10 × raceway cover sections totaling approximately 3.5 feet; connectors, end caps, and bend fittings included for a complete installation
- 25 × 16mm mid-size profile accommodates two to three cables (e.g., CAT5/6 + coaxial, or multiple CAT5/6) in a single raceway run — more capacity than the CW1510-KIT without requiring the full-width CW4016
- PVC raceway with adhesive backing; white finish; all included fittings are the same 25 × 16mm profile as the CW2516 sections
- For longer or more complex installations
$78.00Low Price Guarantee - $1.60SKU: CW2516-H
ENS CW2516-H Raceway Connector, Rectangular, 0.98" W × 0.63" H
- Raceway connector, 0.98" W × 0.63" H, rectangular; joins two CW2516 25 × 16mm raceway sections end-to-end in a straight line
- Maintains a continuous enclosed cable channel across the joint between two 5-foot CW2516 sections — one connector required at each junction between raceway pieces in a straight run
- Sized for the 25 × 16mm CW2516 profile; white PVC; not interchangeable with CW1510-H or CW4016-H fittings
- Also used to couple CW2516 sections to end caps, bends, flat bends, and tee fittings
$1.60Low Price Guarantee - $1.60SKU: CW2516-C
ENS CW2516-C Raceway External Bend, Rectangular, 0.98" W × 0.63" H
- External (outside corner) 90° bend fitting for CW2516 25 × 16mm rectangular cable raceway; provides a clean 90° transition at outside wall corners and protruding edges
- Used when the CW2516 raceway must navigate around an outside building corner, pillar edge, or other convex 90° surface transition
- Sized for the 25 × 16mm CW2516 profile; white PVC; pair with CW2516-B (internal bend) for inside corners
$1.60Low Price Guarantee - $1.60SKU: CW2516-B
ENS CW2516-B Raceway Internal Bend, Rectangular, 0.98" W × 0.63" H
- Internal (inside corner) 90° bend fitting for CW2516 25 × 16mm rectangular cable raceway; provides a clean 90° transition at inside wall corners
- Allows the CW2516 raceway to turn at an inside corner where two walls meet at an interior angle without cutting or bending the raceway channel
- Sized for the 25 × 16mm CW2516 profile; white PVC; pair with CW2516-C (external bend) for outside corners and CW2516-L (flat bend) for same-plane 90° turns
$1.60Low Price Guarantee - $1.60SKU: CW2516-A
ENS CW2516-A Raceway End Cap, Rectangular, 0.98" W × 0.63" H
- End cap for CW2516 25 × 16mm (0.98" W × 0.63" H) rectangular cable raceway; covers the open terminal end of a CW2516 raceway run at each cable entry or exit point
- Provides a clean, professional finished appearance at raceway termination points — exposed open ends leave cut edges visible and the cable inside the raceway unprotected at the termination
- Snaps onto the terminal end of the CW2516 raceway base and cover; white PVC; sized specifically for the 25 × 16mm CW2516 profile
$1.60Low Price Guarantee - $16.00SKU: CW2516
ENS CW2516 Raceway Cord Cover, 5 Feet with Adhesive Backing, Rectangular
- Rectangular PVC surface-mount cable raceway; 25mm wide × 16mm tall (0.98" W × 0.63" H); 5-foot section with adhesive backing
- Mid-size profile in the ENS CW series — larger capacity than the CW1510 (15 × 10mm) for multi-cable runs, and more compact than the CW4016 (40 × 16mm) for installations where the largest profile is not required
- Adhesive backing for tool-free quick mounting on flat wall surfaces; can also be screw-mounted through the base for additional security
- Snap-on cover allows cables to be laid into the base channel after mounting, then covered without threading; cables can be added or removed without removing the raceway
$16.00Low Price Guarantee - $1.60SKU: CW1510-T
ENS CW1510-T Raceway Equal Tee, 15 x 10mm, Rectangular
- Equal tee (T-junction) fitting for CW1510 15 × 10mm rectangular cable raceway; splits one raceway run into two perpendicular branches, or merges two incoming raceway runs into one outgoing run
- Raceway equal tee, 15 × 10mm, rectangular; three equal-sized openings for splitting or merging CW1510 raceway runs at a T-junction
- Used when a camera cable run must branch off to serve two separate cameras, devices, or endpoints from a single cable route along a wall or ceiling
- All three tee openings are the same 15 × 10mm profile — any of the three ports can be used as the incoming run and either of the other two as the outgoing branch
$1.60Low Price Guarantee - $1.60SKU: CW1510-L
ENS CW1510-L Raceway Flat Bend, 15 x 10mm, Rectangular
- Flat 90° bend fitting for CW1510 15 × 10mm rectangular cable raceway; provides a 90° directional change within the same plane (horizontal turn along a wall, baseboard, or ceiling surface)
- Used when the raceway must change direction 90° along a flat surface
- Pre-molded fitting ensures a consistent, professional 90° flat turn without cutting or bending the raceway section
- Sized specifically for the 15 × 10mm CW1510 profile; white PVC
$1.60Low Price Guarantee - $64.00SKU: CW1510-KIT
ENS CW1510-KIT Raceway Cord Cover Kit, 3.5 Feet (10 Covers), Connectors & Accessories Included
- Complete CW1510 15 × 10mm raceway kit; 10 × raceway cover sections totaling approximately 3.5 feet; connectors and fittings included for a complete installation
- 15 × 10mm profile; smallest raceway in the ENS CW series; suited for single CAT5/6 or coaxial cable runs with minimal wall footprint
- PVC raceway with adhesive backing; white finish; all included fittings are the same 15 × 10mm profile as the CW1510 base covers
$64.00Low Price Guarantee
Installation Tools & Supplies Frequently Asked Questions
What tools do I need to install a surveillance camera?
To install a surveillance camera, you'll typically need a drill, screwdriver, and various installation tools like cable strippers and crimpers. Additionally, having a level and measuring tape can help ensure proper placement. Depending on the type of camera, you may also need specific cables, connectors, and mounting hardware, which are often included in the camera kit.
How do I choose the right cable for my surveillance system?
The right cable for a surveillance system depends on the camera type and distance from the recording device. Common options include coaxial cables for analog cameras and Ethernet cables for IP cameras. Ensure the cable is compatible with your system's specifications, such as gauge and shielding type, to maintain video quality and prevent interference.
What is the purpose of a keystone jack in surveillance installation?
A keystone jack is used to connect cables in a structured wiring system, providing a secure and organized way to connect surveillance cameras to networking equipment. It allows for easy insertion and removal of cables, facilitating maintenance and upgrades. Using keystone jacks can help manage cable clutter and improve the overall aesthetics of your installation.
Do I need special tools for terminating alarm wire?
Yes, terminating alarm wire requires specific tools, such as a wire stripper, crimper, and possibly a punch-down tool for connecting wires to terminals. These tools ensure proper connections and minimize signal loss, which is crucial for the reliability of your alarm system. Using the right tools can also prevent damage to the wires during the termination process.
What should I consider when selecting installation supplies for my surveillance system?
When selecting installation supplies, consider the type of surveillance system, the environment (indoor or outdoor), and the distance between components. Look for high-quality cables, connectors, and tools that match the specifications of your cameras and recording devices. Additionally, ensure that the supplies are compatible with the installation location to avoid issues like signal loss or physical damage.
Filter
Shopping Options
