Installation Tools & Supplies
- $1.60SKU: CW4016-L
ENS CW4016-L Raceway Flat Bend, Rectangular, 1.57" W × 0.63" H
- Flat 90° bend fitting for CW4016 40 × 16mm (1.57" W × 0.63" H) rectangular cable raceway; provides a 90° directional change within the same plane
- Used for same-plane 90° turns — such as routing the main cable trunk along a baseboard and turning left or right at a room corner while remaining flat against the floor-level wall — distinct from inside corner (CW4016-B) and outside corner (CW4016-C) bend fittings
- Sized for the 40 × 16mm CW4016 profile; white PVC; not interchangeable with CW1510-L or CW2516-L fittings
- Pre-molded fitting ensures a consistent, professional 90° flat turn without cutting or bending the raceway sections
$1.60Low Price Guarantee - $94.00SKU: CW4016-KIT
ENS CW4016-KIT Raceway Cord Cover Kit, 3.5 Feet (10 Covers), Connectors & Accessories Included
- Complete CW4016 40 × 16mm raceway kit; 10 × raceway cover sections totaling approximately 3.5 feet; end caps, connectors, and bend fittings included for a complete installation without ordering components separately
- 40 × 16mm profile — the largest in the ENS CW series — accommodates three to four cables simultaneously (multiple CAT5/6 and coaxial cables in a single raceway channel); the correct kit for multi-camera main cable trunk runs
- PVC raceway with adhesive backing; white finish; all included fittings are the same 40 × 16mm profile as the CW4016 covers
- For longer or more complex installations
$94.00Low Price Guarantee - $1.60SKU: CW4016-H
ENS CW4016-H Raceway Connector, Rectangular, 1.57" W × 0.63" H
- In-line connector for CW4016 40 × 16mm (1.57" W × 0.63" H) rectangular cable raceway; joins two CW4016 sections end-to-end in a straight line
- Maintains a continuous enclosed cable channel across the joint between two 5-foot CW4016 sections — prevents cable from being exposed at the joint between pieces
- Essential for multi-section installations where the total cable run exceeds 5 feet; one connector per joint between raceway sections in a straight run
$1.60Low Price Guarantee - $1.60SKU: CW4016-C
ENS CW4016-C Raceway External Bend, Rectangular, 1.57" W × 0.63" H
- External (outside corner) 90° bend fitting for CW4016 40 × 16mm (1.57" W × 0.63" H) rectangular cable raceway; provides a clean 90° transition at outside wall corners and protruding edges
- Used when the CW4016 raceway must turn around an outside building corner, pillar edge, or other convex 90° surface — routing the cable trunk continuously from one wall face to the adjacent face without any exposed cable
- Sized for the 40 × 16mm CW4016 profile; white PVC; not interchangeable with CW1510-C or CW2516-C fittings
- Pair with CW4016-B (internal bend) for inside corners
$1.60Low Price Guarantee - $1.60SKU: CW4016-B
ENS CW4016-B Raceway Internal Bend, Rectangular, 1.57" W × 0.63" H
- Internal (inside corner) 90° bend fitting for CW4016 40 × 16mm (1.57" W × 0.63" H) rectangular cable raceway; provides a clean 90° transition at inside wall corners
- Allows the CW4016 raceway to turn at an inside corner where two walls meet at an interior angle — maintaining the enclosed cable channel across the corner without any cutting or bending of the raceway sections
- Sized for the 40 × 16mm CW4016 profile; white PVC; not interchangeable with CW1510-B (15 × 10mm) or CW2516-B (25 × 16mm) fittings
$1.60Low Price Guarantee - $1.60SKU: CW4016-A
ENS CW4016-A Raceway End Cap, Rectangular, 1.57" W × 0.63" H
- End cap for CW4016 40 × 16mm (1.57" W × 0.63" H) rectangular cable raceway; covers and seals the open terminal end of a CW4016 raceway run
- The largest end cap in the ENS CW series — sized for the 40mm wide × 16mm tall CW4016 profile; not interchangeable with CW2516-A (0.98" W × 0.63" H) or CW1510-A (15 × 10mm) end caps
- Provides a clean, professional finished appearance at each raceway termination point where cables enter or exit the raceway channel
- Snaps onto the terminal end of the CW4016 base and cover; white PVC; typically two end caps used per independent raceway run
$1.60Low Price Guarantee - $18.00SKU: CW4016
ENS CW4016 Raceway Cord Cover, 5 Feet, 1.57" W × 0.63" H with Adhesive Backing, Rectangular
- Rectangular PVC surface-mount cable raceway; 40mm wide × 16mm tall (1.57" W × 0.63" H); 5-foot section with adhesive backing
- Adhesive backing for quick tool-free mounting on flat wall surfaces; can also be screw-mounted through the base for permanent installation; same hinged/snap-on cover design as the CW1510 and CW2516 for easy cable insertion after mounting
- White PVC; pairs with CW4016 series fittings: end caps (CW4016-A) and the complete CW4016 fitting family for corners, connectors, flat bends, and tees
$18.00Low Price Guarantee - $1.60SKU: CW2516-T
ENS CW2516-T Raceway Equal Tee, Rectangular, 0.98" W × 0.63" H
- Raceway equal tee, 0.98" W × 0.63" H, rectangular; three equal 25 × 16mm openings for splitting or merging CW2516 raceway runs at a T-junction
- Used when a cable run must branch from one direction into two perpendicular directions
- All three tee openings are the same 25 × 16mm profile; any port can serve as incoming or outgoing
$1.60Low Price Guarantee - $1.60SKU: CW2516-L
ENS CW2516-L Raceway Flat Bend, Rectangular, 0.98" W × 0.63" H
- Flat 90° bend fitting for CW2516 25 × 16mm rectangular cable raceway; provides a 90° directional change within the same plane (horizontal turn along a wall, baseboard, or ceiling)
- Used for same-plane 90° turns — distinct from internal bends (CW2516-B, inside corners) and external bends (CW2516-C, outside corners) which handle vertical-to-horizontal corner transitions
- Sized for the 25 × 16mm CW2516 profile; white PVC; not interchangeable with CW1510-L or CW4016-L fittings
$1.60Low Price Guarantee
Installation Tools & Supplies Frequently Asked Questions
What tools do I need to install a surveillance camera?
To install a surveillance camera, you'll typically need a drill, screwdriver, and various installation tools like cable strippers and crimpers. Additionally, having a level and measuring tape can help ensure proper placement. Depending on the type of camera, you may also need specific cables, connectors, and mounting hardware, which are often included in the camera kit.
How do I choose the right cable for my surveillance system?
The right cable for a surveillance system depends on the camera type and distance from the recording device. Common options include coaxial cables for analog cameras and Ethernet cables for IP cameras. Ensure the cable is compatible with your system's specifications, such as gauge and shielding type, to maintain video quality and prevent interference.
What is the purpose of a keystone jack in surveillance installation?
A keystone jack is used to connect cables in a structured wiring system, providing a secure and organized way to connect surveillance cameras to networking equipment. It allows for easy insertion and removal of cables, facilitating maintenance and upgrades. Using keystone jacks can help manage cable clutter and improve the overall aesthetics of your installation.
Do I need special tools for terminating alarm wire?
Yes, terminating alarm wire requires specific tools, such as a wire stripper, crimper, and possibly a punch-down tool for connecting wires to terminals. These tools ensure proper connections and minimize signal loss, which is crucial for the reliability of your alarm system. Using the right tools can also prevent damage to the wires during the termination process.
What should I consider when selecting installation supplies for my surveillance system?
When selecting installation supplies, consider the type of surveillance system, the environment (indoor or outdoor), and the distance between components. Look for high-quality cables, connectors, and tools that match the specifications of your cameras and recording devices. Additionally, ensure that the supplies are compatible with the installation location to avoid issues like signal loss or physical damage.
Filter
Shopping Options
