Installation Tools & Supplies
- $4.10SKU: CJ0201-M
ENS CJ0201-M J Hook 123 x 67 x 33mm
- Medium J hook cable support; dimensions: 123mm (approximately 4.8") wide × 67mm (approximately 2.6") deep × 33mm (approximately 1.3") tall
- The medium hook width suits typical 3–6 cable bundle runs — the standard bundle size for a few Cat6 cables or a mix of Cat6 and coaxial cables routed together from a camera cluster to a central distribution point
- J saddle profile supports cables without pinching, crushing, or exceeding minimum bend radius; installs on hanger wire, beam flange, or ceiling grid support wire
$4.10Low Price Guarantee - $8.70SKU: CJ0201-L
ENS CJ0201-L J Hook 177.8 x 101.6 x 50.8mm
- Large J hook cable support; dimensions: 177.8mm (7") wide × 101.6mm (4") deep × 50.8mm (2") tall; for routing and supporting large bundles of low-voltage cables in above-ceiling and structural spaces
- The large 177.8mm width accommodates wide cable bundles — multiple Cat6, coaxial, and alarm cable runs grouped together in a single above-ceiling cable support — reducing the number of hooks required per linear foot of cable route
- J hook saddle profile: cables rest in the J-shaped trough without being pinched, crushed, or bent beyond their minimum bend radius — maintaining Cat6 performance standards that prohibit excessive bend radius or cable compression
$8.70Low Price Guarantee - $18.00SKU: CCKIT-WH
ENS CCKIT-WH Nail-In Clips Kit, 50 Pieces CC8S-WH, 20 Pieces CC16D-WH, 20 Pieces CC24D-WH
- Nail-in clips kit: 50 × CC8S-WH (8mm single, white), 20 × CC16D-WH (16mm dual, white), 20 × CC24D-WH (24mm dual, white); 90 clips total in assorted sizes for complete security cable runs
- All clips in white for clean, inconspicuous installation on white baseboards, door frames, and wall surfaces; all nail-in fasteners for hammer-drive installation into wood surfaces without separate screws, anchors, or drill
- Saves time during ordering and jobsite preparation — a single kit covers all cable sizes for a typical one- to four-camera installation without carrying three separate bags
- For larger jobs requiring higher clip counts
$18.00Low Price Guarantee - $12.00SKU: CC8S-WH
ENS CC8S-WH Nail-In Clips, 8mm, White, 100-Pack
- Single nail-in cable clip; 8mm cable diameter; white; 100-pack; single cable per clip body
- 8mm diameter: specifically sized for small-diameter low-voltage cables — 22/4 alarm wire, 18/2 speaker wire, thermostat wire, and similarly thin cable types that require a snug-fitting clip to prevent movement and rattling against the surface
- Nail-in fastener for fast hammer-drive installation into wood surfaces without additional tools; the larger 100-pack (vs. 50-pack for larger clips) reflects the higher clip density typically needed for small-wire runs
$12.00Low Price Guarantee - $18.00SKU: CC24D-WH
ENS CC24D-WH Dual Nail-In Clips, 24mm, White, 50-Pack
- Dual nail-in cable clip; 24mm cable diameter; white; 50-pack; accommodates two cables simultaneously
- 24mm clip opening: correct specification for larger-diameter cables (RG6 coax, jacketed Cat6, bundled cable runs) that do not fit within the 16mm CC16D-WH clip; dual body allows two cables side-by-side in one clip
- Nail-in fastener: driven into wood surfaces with a hammer — the fastest cable clip installation method for wood surface runs; no screwdriver, drill, or anchor required
- White color for inconspicuous installation on white baseboards, door frames, and wall surfaces
$18.00Low Price Guarantee - $14.00SKU: CC16D-WH
ENS CC16D-WH Dual Nail-In Clips, 16mm, White, 50-Pack
- Dual nail-in cable clip; 16mm cable diameter; white; 50-pack; accommodates two cables simultaneously in a single clip
- Nail-in fastener: the clip is driven into wood surfaces (baseboards, door frames, wood studs) with a hammer — no drill, screwdriver, or anchor required; fastest installation method for wood surface cable runs
- 16mm diameter: sized for standard RG59 coaxial cable (approximately 6mm OD) in a dual-capacity body, or for a single larger cable up to the clip's internal diameter; confirm cable diameters before ordering
- White color for clean
$14.00Low Price Guarantee - $778.00SKU: MC510-5-IP
ENS MC510-5-IP 5" IPS Touch Screen, Cable Tester
- 5.4-inch touch screen, 1920x1152 resolutions
- 8MP CVI/ TVI/ AHD PoE, IP Analog camera test
- H.265/H.264, 4K video display via mainstream
- VGA input, support 1920 x 1200P 60FPS
- HDMI Input, support 4K 30FPS
$778.00Low Price Guarantee - $25.90SKU: JIC-2030
ENS JIC-2030 Wire Stripper for Cutting and Stripping Wires 20 - 30AWG
- Support HDMI 1.4/HDCP1.4
- Support local loop-out
- Support 120m long distance transmission
- Low power consumption, low temperature and high safety
- Support IR control
$25.90Low Price Guarantee - $25.90SKU: JIC-1022
ENS JIC-1022 Wire Stripper for Cutting and Stripping Wires 10 to 22 AWG
- Perfect for stripping 2 to 3 mm fiber jackets off of fiber optic cables without damaging the fiber
- Coil spring reduces hand fatigue when using the tool for extended periods of time
- Conveniently located bending makes wire looping quick and easy
- 50 HRC black oxide finish enhances strength and durability of the tool
- Cutting edges are hardened, tempered, and ground for superior cutting and stripping
$25.90Low Price Guarantee
Installation Tools & Supplies Frequently Asked Questions
What tools do I need to install a surveillance camera?
To install a surveillance camera, you'll typically need a drill, screwdriver, and various installation tools like cable strippers and crimpers. Additionally, having a level and measuring tape can help ensure proper placement. Depending on the type of camera, you may also need specific cables, connectors, and mounting hardware, which are often included in the camera kit.
How do I choose the right cable for my surveillance system?
The right cable for a surveillance system depends on the camera type and distance from the recording device. Common options include coaxial cables for analog cameras and Ethernet cables for IP cameras. Ensure the cable is compatible with your system's specifications, such as gauge and shielding type, to maintain video quality and prevent interference.
What is the purpose of a keystone jack in surveillance installation?
A keystone jack is used to connect cables in a structured wiring system, providing a secure and organized way to connect surveillance cameras to networking equipment. It allows for easy insertion and removal of cables, facilitating maintenance and upgrades. Using keystone jacks can help manage cable clutter and improve the overall aesthetics of your installation.
Do I need special tools for terminating alarm wire?
Yes, terminating alarm wire requires specific tools, such as a wire stripper, crimper, and possibly a punch-down tool for connecting wires to terminals. These tools ensure proper connections and minimize signal loss, which is crucial for the reliability of your alarm system. Using the right tools can also prevent damage to the wires during the termination process.
What should I consider when selecting installation supplies for my surveillance system?
When selecting installation supplies, consider the type of surveillance system, the environment (indoor or outdoor), and the distance between components. Look for high-quality cables, connectors, and tools that match the specifications of your cameras and recording devices. Additionally, ensure that the supplies are compatible with the installation location to avoid issues like signal loss or physical damage.
Filter
Shopping Options
