Active Vision LSDI Installation Tools & Supplies
Filter
- $143.00SKU: LS-81-000
LSDI LS-81-000 Creep-ZitTM Pro 36 Ft Threaded Connector Wire Running Rod Kit
- Five FiberFuseTM 6 ft. push/pull rods with
- Male and female threaded connector ends
- One luminous (glows in the dark) FiberFuseTM 6 ft. push/pull rod with male and female threaded connector ends
- One threaded connector 6 ft. Fish-TailzTM 1/8″ diameter mesh pull sock
- Luminous whisk threaded connector tip
$143.00Low Price Guarantee - $68.04SKU: LS-54-105
LSDI LS-54-105 P-1 Portasol Soldering Kit
- Assorted spare tips
- Flint ignition
- 60 minute run time
- Anti Static ESD Safe
- Ready to melt solder less than 30 seconds from ignition
$68.04Low Price Guarantee - $47.75SKU: LS-62-338
LSDI LS-62-338 3/8” ReBore-Zit (1/4” Pilot Size)
- The bit is fabricated with a hollow bodied drill bit containing a free spinning, swivel eyelet mounted to its pilot hole center shaft.
- The bit will not twist the wire.
- ReBore-Zit bit to accommodate the preexisting hole
- step-up in ReBore-Zit sizes until you obtain your desired final hole size.
- The ReBore-Zit the Standard 3/8″
$47.75Low Price Guarantee - $1,447.99SKU: LS-80-610
LSDI LS-80-610 RoyRodsTM All-Tool-Mate Master Tool Kit (USA Only)
- LS-81-700 RoyRodsTM Pro 36″
- LS-81-709 RoyRodsTM Drag-Zit Magnet
- LS-81-706 Z-Tip Quick Connect Tip
- LS-81-707 J-Tip Quick Connect Tip
- LS-81-708 RoyRodsTM Female/Bullnose
$1,447.99Low Price Guarantee - $1,171.00SKU: LS-80-600
LSDI LS-80-600 All-Tool-Mate Master Threaded Tool Kit (USA Only)
- LS-81-000 Creep-Zit Pro 36″
- LS-81-360 Creep-Zit Drag-Zit Magnet
- LS-82-350 Z-Tip Push/Pull Tip
- LS-82-370 J-Tip Hook
- LS-81-300 Creep-Zit Replacement Threaded
$1,171.00Low Price Guarantee - $175.00SKU: LS-56-115
LSDI LS-56-115 12” Double Blade Hole Cutter
- For cutting round holes in ceilings, walls and floors
- Cuts veneer, plywood, sheet rock (gypsum board), f iberglass, fiber cement board, plaster, stucco, etc.
- Can be used with either hand drill or pillar drill
- Maximum cutting depth: 2″ (50 mm)
- Maximum cutting diameter: 12″ (305 mm)
$175.00Low Price Guarantee - $130.00SKU: LS-85-330
LSDI LS-85-330 YFTTM 30 Fret Yellow Epoxy Fish Tape in case
- Fiberglass Fish Tapes are designed with the patented FiberFuseTM process, are continuous length rods which are smaller in diameter (.120″) than your Creep-Zit rods (.175″) and have no rigid connectors
- When flexibility is important, these fish tapes are the perfect solution
- Designed for conduit and tight rod runs that might otherwise stress your standard Creep-Zit rods
- Metal bullnose tip with push/pull eye on both ends. Ball chain with clip included on one end
$130.00Low Price Guarantee - $113.05SKU: LS-56-015
LSDI LS-56-015 10” Double Blade Hole Cutter
- Adjust to desired width and depth
- Attach to drill Pilot Drill Bit Blades Durable case included: 13″ x 14″ DESCRIPTION 10″ Double Blade Hole Cutter Replacement Blades for 10″ Hole Cutter
- Remove safety caps from blades and pilot bit
- Always wear safety glasses when using product
- Verify that there are no electrical components behind the surface to be drilled
$113.05Low Price Guarantee - $105.00SKU: LS-62-368
LSDI LS-62-368 3/4” ReBore-Zit (3/8” Pilot Size)
- The bit is fabricated with a hollow bodied drill bit containing a free spinning, swivel eyelet mounted to its pilot hole center shaft.
- The bit will not twist the wire.
- ReBore-Zit bit to accommodate the preexisting hole
- step-up in ReBore-Zit sizes until you obtain your desired final hole size.
- The ReBore-Zit the Standard 3/4″
$105.00Low Price Guarantee
Installation Tools & Supplies Frequently Asked Questions
What tools do I need to install a surveillance camera?
To install a surveillance camera, you'll typically need a drill, screwdriver, and various installation tools like cable strippers and crimpers. Additionally, having a level and measuring tape can help ensure proper placement. Depending on the type of camera, you may also need specific cables, connectors, and mounting hardware, which are often included in the camera kit.
How do I choose the right cable for my surveillance system?
The right cable for a surveillance system depends on the camera type and distance from the recording device. Common options include coaxial cables for analog cameras and Ethernet cables for IP cameras. Ensure the cable is compatible with your system's specifications, such as gauge and shielding type, to maintain video quality and prevent interference.
What is the purpose of a keystone jack in surveillance installation?
A keystone jack is used to connect cables in a structured wiring system, providing a secure and organized way to connect surveillance cameras to networking equipment. It allows for easy insertion and removal of cables, facilitating maintenance and upgrades. Using keystone jacks can help manage cable clutter and improve the overall aesthetics of your installation.
Do I need special tools for terminating alarm wire?
Yes, terminating alarm wire requires specific tools, such as a wire stripper, crimper, and possibly a punch-down tool for connecting wires to terminals. These tools ensure proper connections and minimize signal loss, which is crucial for the reliability of your alarm system. Using the right tools can also prevent damage to the wires during the termination process.
What should I consider when selecting installation supplies for my surveillance system?
When selecting installation supplies, consider the type of surveillance system, the environment (indoor or outdoor), and the distance between components. Look for high-quality cables, connectors, and tools that match the specifications of your cameras and recording devices. Additionally, ensure that the supplies are compatible with the installation location to avoid issues like signal loss or physical damage.
Filter
Now Shopping by
Shopping Options 