Cable Management
- $1.60SKU: CW2516-A
ENS CW2516-A Raceway End Cap, Rectangular, 0.98" W × 0.63" H
- End cap for CW2516 25 × 16mm (0.98" W × 0.63" H) rectangular cable raceway; covers the open terminal end of a CW2516 raceway run at each cable entry or exit point
- Provides a clean, professional finished appearance at raceway termination points — exposed open ends leave cut edges visible and the cable inside the raceway unprotected at the termination
- Snaps onto the terminal end of the CW2516 raceway base and cover; white PVC; sized specifically for the 25 × 16mm CW2516 profile
$1.60Low Price Guarantee - $16.00SKU: CW2516
ENS CW2516 Raceway Cord Cover, 5 Feet with Adhesive Backing, Rectangular
- Rectangular PVC surface-mount cable raceway; 25mm wide × 16mm tall (0.98" W × 0.63" H); 5-foot section with adhesive backing
- Mid-size profile in the ENS CW series — larger capacity than the CW1510 (15 × 10mm) for multi-cable runs, and more compact than the CW4016 (40 × 16mm) for installations where the largest profile is not required
- Adhesive backing for tool-free quick mounting on flat wall surfaces; can also be screw-mounted through the base for additional security
- Snap-on cover allows cables to be laid into the base channel after mounting, then covered without threading; cables can be added or removed without removing the raceway
$16.00Low Price Guarantee - $1.60SKU: CW1510-T
ENS CW1510-T Raceway Equal Tee, 15 x 10mm, Rectangular
- Equal tee (T-junction) fitting for CW1510 15 × 10mm rectangular cable raceway; splits one raceway run into two perpendicular branches, or merges two incoming raceway runs into one outgoing run
- Raceway equal tee, 15 × 10mm, rectangular; three equal-sized openings for splitting or merging CW1510 raceway runs at a T-junction
- Used when a camera cable run must branch off to serve two separate cameras, devices, or endpoints from a single cable route along a wall or ceiling
- All three tee openings are the same 15 × 10mm profile — any of the three ports can be used as the incoming run and either of the other two as the outgoing branch
$1.60Low Price Guarantee - $1.60SKU: CW1510-L
ENS CW1510-L Raceway Flat Bend, 15 x 10mm, Rectangular
- Flat 90° bend fitting for CW1510 15 × 10mm rectangular cable raceway; provides a 90° directional change within the same plane (horizontal turn along a wall, baseboard, or ceiling surface)
- Used when the raceway must change direction 90° along a flat surface
- Pre-molded fitting ensures a consistent, professional 90° flat turn without cutting or bending the raceway section
- Sized specifically for the 15 × 10mm CW1510 profile; white PVC
$1.60Low Price Guarantee - $64.00SKU: CW1510-KIT
ENS CW1510-KIT Raceway Cord Cover Kit, 3.5 Feet (10 Covers), Connectors & Accessories Included
- Complete CW1510 15 × 10mm raceway kit; 10 × raceway cover sections totaling approximately 3.5 feet; connectors and fittings included for a complete installation
- 15 × 10mm profile; smallest raceway in the ENS CW series; suited for single CAT5/6 or coaxial cable runs with minimal wall footprint
- PVC raceway with adhesive backing; white finish; all included fittings are the same 15 × 10mm profile as the CW1510 base covers
$64.00Low Price Guarantee - $1.60SKU: CW1510-H
ENS CW1510-H Raceway Connector, 15 x 10mm, Rectangular
- Raceway connector, 15 × 10mm, rectangular; joins two CW1510 raceway sections end-to-end in a straight line
- Used at straight-line joints between two 5-foot CW1510 raceway sections — the connector bridges the gap between sections, maintaining a continuous enclosed channel and preventing the cable from being exposed at the joint
- Essential for installations where the total cable run exceeds 5 feet and multiple CW1510 sections must be chained end-to-end; provides a professional, seamless joint between sections
- Sized specifically for the 15 × 10mm CW1510 profile; white PVC; one connector required per junction between raceway sections
$1.60Low Price Guarantee - $1.60SKU: CW1510-C
ENS CW1510-C Raceway External Bend, 15 x 10mm, Rectangular
- External (outside corner) 90° bend fitting for CW1510 15 × 10mm rectangular cable raceway; provides a clean 90° directional transition at outside wall corners and protruding edges
- Used when the raceway travels along a wall face and must turn outward around an outside corner — such as at the corner of a building, a pillar, or a protruding wall section
- Pre-molded external bend eliminates the need to cut miter angles in raceway sections at outside corners; ensures consistent, professional fitting at every outside corner
$1.60Low Price Guarantee - $1.60SKU: CW1510-B
ENS CW1510-B Raceway Internal Bend, 15 x 10mm, Rectangular
- Internal (inside corner) 90° bend fitting for CW1510 15 × 10mm rectangular cable raceway; provides a clean 90° directional transition at inside wall corners
- Eliminates the need to cut, miter, or bend raceway sections to navigate inside corners; the pre-molded bend ensures a consistent, professional fit at every inside corner
- Snaps into the CW1510 base channel ends at the corner; the raceway cover sections abut the bend fitting for a continuous, sealed appearance
- Sized specifically for the 15 × 10mm CW1510 profile; white PVC; pair with CW1510-C (external bend) for outside corners
$1.60Low Price Guarantee - $1.60SKU: CW1510-A
ENS CW1510-A Raceway End Cap, 15 x 10mm, Rectangular
- End cap for CW1510 15 × 10mm rectangular cable raceway; covers and seals the open terminal ends of a CW1510 raceway run
- Provides a professional, finished appearance at each raceway termination point — without end caps, the open ends of raceway sections expose the cable inside and leave unfinished cut edges visible at the wall
- Snaps onto the terminal end of the CW1510 raceway base and cover; no adhesive or fasteners required in most installations
- Sized specifically for the 15 × 10mm CW1510 profile — not interchangeable with CW2516-A or CW4016-A end caps
$1.60Low Price Guarantee
Filter
Shopping Options
