Cable Management
- $18.00SKU: CCKIT-WH
ENS CCKIT-WH Nail-In Clips Kit, 50 Pieces CC8S-WH, 20 Pieces CC16D-WH, 20 Pieces CC24D-WH
- Nail-in clips kit: 50 × CC8S-WH (8mm single, white), 20 × CC16D-WH (16mm dual, white), 20 × CC24D-WH (24mm dual, white); 90 clips total in assorted sizes for complete security cable runs
- All clips in white for clean, inconspicuous installation on white baseboards, door frames, and wall surfaces; all nail-in fasteners for hammer-drive installation into wood surfaces without separate screws, anchors, or drill
- Saves time during ordering and jobsite preparation — a single kit covers all cable sizes for a typical one- to four-camera installation without carrying three separate bags
- For larger jobs requiring higher clip counts
$18.00Low Price Guarantee - $12.00SKU: CC8S-WH
ENS CC8S-WH Nail-In Clips, 8mm, White, 100-Pack
- Single nail-in cable clip; 8mm cable diameter; white; 100-pack; single cable per clip body
- 8mm diameter: specifically sized for small-diameter low-voltage cables — 22/4 alarm wire, 18/2 speaker wire, thermostat wire, and similarly thin cable types that require a snug-fitting clip to prevent movement and rattling against the surface
- Nail-in fastener for fast hammer-drive installation into wood surfaces without additional tools; the larger 100-pack (vs. 50-pack for larger clips) reflects the higher clip density typically needed for small-wire runs
$12.00Low Price Guarantee - $18.00SKU: CC24D-WH
ENS CC24D-WH Dual Nail-In Clips, 24mm, White, 50-Pack
- Dual nail-in cable clip; 24mm cable diameter; white; 50-pack; accommodates two cables simultaneously
- 24mm clip opening: correct specification for larger-diameter cables (RG6 coax, jacketed Cat6, bundled cable runs) that do not fit within the 16mm CC16D-WH clip; dual body allows two cables side-by-side in one clip
- Nail-in fastener: driven into wood surfaces with a hammer — the fastest cable clip installation method for wood surface runs; no screwdriver, drill, or anchor required
- White color for inconspicuous installation on white baseboards, door frames, and wall surfaces
$18.00Low Price Guarantee - $14.00SKU: CC16D-WH
ENS CC16D-WH Dual Nail-In Clips, 16mm, White, 50-Pack
- Dual nail-in cable clip; 16mm cable diameter; white; 50-pack; accommodates two cables simultaneously in a single clip
- Nail-in fastener: the clip is driven into wood surfaces (baseboards, door frames, wood studs) with a hammer — no drill, screwdriver, or anchor required; fastest installation method for wood surface cable runs
- 16mm diameter: sized for standard RG59 coaxial cable (approximately 6mm OD) in a dual-capacity body, or for a single larger cable up to the clip's internal diameter; confirm cable diameters before ordering
- White color for clean
$14.00Low Price Guarantee - $1.60SKU: CW4016-T
ENS CW4016-T Raceway Equal Tee, Rectangular, 1.57" W × 0.63" H
- Equal tee (T-junction) fitting for CW4016 40 × 16mm (1.57" W × 0.63" H) rectangular cable raceway; three equal 40 × 16mm openings for splitting or merging raceway runs at a T-junction
- Used when the CW4016 main cable trunk must branch to serve two directions simultaneously
- All three tee openings are the same 40 × 16mm profile; any port can serve as the incoming trunk and either of the other two as the branch outputs
$1.60Low Price Guarantee - $1.60SKU: CW4016-L
ENS CW4016-L Raceway Flat Bend, Rectangular, 1.57" W × 0.63" H
- Flat 90° bend fitting for CW4016 40 × 16mm (1.57" W × 0.63" H) rectangular cable raceway; provides a 90° directional change within the same plane
- Used for same-plane 90° turns — such as routing the main cable trunk along a baseboard and turning left or right at a room corner while remaining flat against the floor-level wall — distinct from inside corner (CW4016-B) and outside corner (CW4016-C) bend fittings
- Sized for the 40 × 16mm CW4016 profile; white PVC; not interchangeable with CW1510-L or CW2516-L fittings
- Pre-molded fitting ensures a consistent, professional 90° flat turn without cutting or bending the raceway sections
$1.60Low Price Guarantee - $94.00SKU: CW4016-KIT
ENS CW4016-KIT Raceway Cord Cover Kit, 3.5 Feet (10 Covers), Connectors & Accessories Included
- Complete CW4016 40 × 16mm raceway kit; 10 × raceway cover sections totaling approximately 3.5 feet; end caps, connectors, and bend fittings included for a complete installation without ordering components separately
- 40 × 16mm profile — the largest in the ENS CW series — accommodates three to four cables simultaneously (multiple CAT5/6 and coaxial cables in a single raceway channel); the correct kit for multi-camera main cable trunk runs
- PVC raceway with adhesive backing; white finish; all included fittings are the same 40 × 16mm profile as the CW4016 covers
- For longer or more complex installations
$94.00Low Price Guarantee - $1.60SKU: CW4016-H
ENS CW4016-H Raceway Connector, Rectangular, 1.57" W × 0.63" H
- In-line connector for CW4016 40 × 16mm (1.57" W × 0.63" H) rectangular cable raceway; joins two CW4016 sections end-to-end in a straight line
- Maintains a continuous enclosed cable channel across the joint between two 5-foot CW4016 sections — prevents cable from being exposed at the joint between pieces
- Essential for multi-section installations where the total cable run exceeds 5 feet; one connector per joint between raceway sections in a straight run
$1.60Low Price Guarantee - $1.60SKU: CW4016-C
ENS CW4016-C Raceway External Bend, Rectangular, 1.57" W × 0.63" H
- External (outside corner) 90° bend fitting for CW4016 40 × 16mm (1.57" W × 0.63" H) rectangular cable raceway; provides a clean 90° transition at outside wall corners and protruding edges
- Used when the CW4016 raceway must turn around an outside building corner, pillar edge, or other convex 90° surface — routing the cable trunk continuously from one wall face to the adjacent face without any exposed cable
- Sized for the 40 × 16mm CW4016 profile; white PVC; not interchangeable with CW1510-C or CW2516-C fittings
- Pair with CW4016-B (internal bend) for inside corners
$1.60Low Price Guarantee
Filter
Shopping Options
