ENS Ties
Filter
- $2.00SKU: CT-6-W
ENS CT-6-W 6'' White Wire Tie, 100Pc/Bag, 40 Lbs Tensile Strength, 3.6*150mm
- 6'' White Wire Tie
- 100Pc/Bag
- 40 Lbs Tensile Strength
- 3.6*150mm
$2.00Low Price Guarantee - $1.60SKU: CW1510-A
ENS CW1510-A Raceway End Cap, 15 x 10mm, Rectangular
- End cap for CW1510 15 × 10mm rectangular cable raceway; covers and seals the open terminal ends of a CW1510 raceway run
- Provides a professional, finished appearance at each raceway termination point — without end caps, the open ends of raceway sections expose the cable inside and leave unfinished cut edges visible at the wall
- Snaps onto the terminal end of the CW1510 raceway base and cover; no adhesive or fasteners required in most installations
- Sized specifically for the 15 × 10mm CW1510 profile — not interchangeable with CW2516-A or CW4016-A end caps
$1.60Low Price Guarantee - $1.60SKU: CW1510-B
ENS CW1510-B Raceway Internal Bend, 15 x 10mm, Rectangular
- Internal (inside corner) 90° bend fitting for CW1510 15 × 10mm rectangular cable raceway; provides a clean 90° directional transition at inside wall corners
- Eliminates the need to cut, miter, or bend raceway sections to navigate inside corners; the pre-molded bend ensures a consistent, professional fit at every inside corner
- Snaps into the CW1510 base channel ends at the corner; the raceway cover sections abut the bend fitting for a continuous, sealed appearance
- Sized specifically for the 15 × 10mm CW1510 profile; white PVC; pair with CW1510-C (external bend) for outside corners
$1.60Low Price Guarantee - $1.60SKU: CW1510-T
ENS CW1510-T Raceway Equal Tee, 15 x 10mm, Rectangular
- Equal tee (T-junction) fitting for CW1510 15 × 10mm rectangular cable raceway; splits one raceway run into two perpendicular branches, or merges two incoming raceway runs into one outgoing run
- Raceway equal tee, 15 × 10mm, rectangular; three equal-sized openings for splitting or merging CW1510 raceway runs at a T-junction
- Used when a camera cable run must branch off to serve two separate cameras, devices, or endpoints from a single cable route along a wall or ceiling
- All three tee openings are the same 15 × 10mm profile — any of the three ports can be used as the incoming run and either of the other two as the outgoing branch
$1.60Low Price Guarantee - $1.60SKU: CW2516-B
ENS CW2516-B Raceway Internal Bend, Rectangular, 0.98" W × 0.63" H
- Internal (inside corner) 90° bend fitting for CW2516 25 × 16mm rectangular cable raceway; provides a clean 90° transition at inside wall corners
- Allows the CW2516 raceway to turn at an inside corner where two walls meet at an interior angle without cutting or bending the raceway channel
- Sized for the 25 × 16mm CW2516 profile; white PVC; pair with CW2516-C (external bend) for outside corners and CW2516-L (flat bend) for same-plane 90° turns
$1.60Low Price Guarantee - $1.60SKU: CW2516-C
ENS CW2516-C Raceway External Bend, Rectangular, 0.98" W × 0.63" H
- External (outside corner) 90° bend fitting for CW2516 25 × 16mm rectangular cable raceway; provides a clean 90° transition at outside wall corners and protruding edges
- Used when the CW2516 raceway must navigate around an outside building corner, pillar edge, or other convex 90° surface transition
- Sized for the 25 × 16mm CW2516 profile; white PVC; pair with CW2516-B (internal bend) for inside corners
$1.60Low Price Guarantee - $1.60SKU: CW4016-C
ENS CW4016-C Raceway External Bend, Rectangular, 1.57" W × 0.63" H
- External (outside corner) 90° bend fitting for CW4016 40 × 16mm (1.57" W × 0.63" H) rectangular cable raceway; provides a clean 90° transition at outside wall corners and protruding edges
- Used when the CW4016 raceway must turn around an outside building corner, pillar edge, or other convex 90° surface — routing the cable trunk continuously from one wall face to the adjacent face without any exposed cable
- Sized for the 40 × 16mm CW4016 profile; white PVC; not interchangeable with CW1510-C or CW2516-C fittings
- Pair with CW4016-B (internal bend) for inside corners
$1.60Low Price Guarantee - $1.60SKU: CW4016-H
ENS CW4016-H Raceway Connector, Rectangular, 1.57" W × 0.63" H
- In-line connector for CW4016 40 × 16mm (1.57" W × 0.63" H) rectangular cable raceway; joins two CW4016 sections end-to-end in a straight line
- Maintains a continuous enclosed cable channel across the joint between two 5-foot CW4016 sections — prevents cable from being exposed at the joint between pieces
- Essential for multi-section installations where the total cable run exceeds 5 feet; one connector per joint between raceway sections in a straight run
$1.60Low Price Guarantee - $1.60SKU: CW4016-L
ENS CW4016-L Raceway Flat Bend, Rectangular, 1.57" W × 0.63" H
- Flat 90° bend fitting for CW4016 40 × 16mm (1.57" W × 0.63" H) rectangular cable raceway; provides a 90° directional change within the same plane
- Used for same-plane 90° turns — such as routing the main cable trunk along a baseboard and turning left or right at a room corner while remaining flat against the floor-level wall — distinct from inside corner (CW4016-B) and outside corner (CW4016-C) bend fittings
- Sized for the 40 × 16mm CW4016 profile; white PVC; not interchangeable with CW1510-L or CW2516-L fittings
- Pre-molded fitting ensures a consistent, professional 90° flat turn without cutting or bending the raceway sections
$1.60Low Price Guarantee
Filter
Now Shopping by
Shopping Options 